LED Rose Tealight Candles

Today I am sharing a project that my daughter absolutely loves. I think at one point she relieved me of 8 of my learning roses and turned them into night lights around her room. Not that I really suggest this, but it showed me how much she loved them.

This project has slightly evolved from where it started. The idea started when seeing this post on pinterest. (if you would like to follow me, my pinterest is here.) Short version, it involves tearing apart a silk rose and gluing the petals to spoons. Then you are supposed to glue the spoons the the flameless tealight. I liked the idea, but I didn't think the light would pass through all that plastic, so I decided to change it a bit.

The making of one rose takes me about 20 minutes (40 if I am taking pictures for the tutorial), and usually one really burnt finger. I am sure it is able to be done without burning yourself, but I am just not that smart apparently.

Here I have three submersible tealights, green, purple, and pink. I really like these, and buy them here. I like them because they are brighter and easier to change the batteries when the time is up. And the options become really awesome.

I also have three white roses that have no stems. I have learned that your best bet is to use the white roses. Yellow ones will work, but after trying every color in the rose spectrum, none of the others were nearly as luminescent as the white. Ultimately, you are going to want a white rose and a colored LED candle of your choice.

First, you have to pop off the stem attachment piece (after removing the stem of course). Sometimes they don't like to budge and are a hassle. Be prepared to have to get a little rough, but not violent.

Now you are going to pull the rose apart, starting with the green....thingy....I don't know what its called.

The entire rose is really just poorly glued together, so you will need to tug and pull. Again, sometimes they can be little buggers, but overall they are easily disassembled. The petals will be either 3 to a layer or 4 as you get closer to the center (there are only 3 layers that will have 4 petals). They will also get smaller as you pull the layers back, so I tend to pile them in order as I pull them apart.

When that is done, you will have a little foam cone. Go ahead and throw this little guy away, we won't be needing him.
Now take your LED apart. It will be a lot easier to just work with the top.

Take the top layer of petals and cut them into 4 pieces. You can see it resulted in almost a templar cross being cut out of the center. This will later turn into triangles as you are cutting apart the 3 petal layers.

Then comes a little line of glue on the bottom of a petal from the hot glue gun. Too much glue will result in hot gluey lava when you have to tap and press the petal into place.

Now you are going to place the petal on the top of your LED. Make sure it is either flush with the line of your LED or slightly above. We don't want anything impeding the ability to screw on the bottom.

You are going to do the exact same thing for the next petal, but directly opposite of where you just put the first one. Then you will do the same with the last two, making your LED top surrounded with its first layer. Once the 4 petals are in place, make sure you have them overlap each other. One petal should both be covered on one side and covering on the other. Hopefully you can see that with this picture.

Here I am just going to take a moment to say that sometimes the petals will get stray strands like they are fraying. it is perfectly acceptable to trim these strands.

You need to repeat the steps again and again with each layer. There is no perfectly right way to put it together, just depends on how you wan your rose to look. If you want a budding rose, you obviously won't use the whole rose, just as much as you want. Here are various stages of building a full rose.

(if you fee like a petal is not secure, like the bottom petal here, you can add a dot of glue where you think it needs the extra help.)

Here is a "full" rose using all of my petals.

Now, you flip the rose over to add the green thingy I previously mentioned that I have no name for. I usually only add three pieces of it, 4 if I like the look.

And you are done!

Here are some pics of these three roses in a natural lit room and a completely dark room.

So awesome! My mom watched me make these while my husband, brother, father, and son were watching the football game. (GO HAWKS!) She wants a blue one and a green one. I showed her how great they work for little night lights in her bathroom. But I also want to show you the awesome that is submerging them in water.

If you use any other rose than white, the dye will bleed into the water, so you will have to wash them first. Isn't this amazing?! I totally would have used them for my wedding decorations if I was using roses. (My flowers were calla lilies and orchids...I couldn't figure out how to make it work with them.)

When I first started making these, my goal was to make a fairy garden around my garden tub in my master bathroom. Eventually that will happen, and when it does, I will give you pics!

Happy crafting.